
Last Updated: November 16, 2026
Quick Summary
The tools for repairing block paving you actually need are a block paving lifter or extractor, a rubber mallet, a bolster chisel, a stiff brush and kiln-dried jointing sand. These hand tools cover almost every lifting and relaying job, and small hand tools are worth buying outright because they cost little and get reused.
- A block paving lifter grips a block and draws it out without damage.
- Lever against the joint, not a neighbouring block edge, to avoid chipping pavers.
- Fix sunken paving by lifting blocks, correcting the bedding layer and relaying level.
- Brush kiln-dried sand into the joints and compact the area to finish.
- Hire cutters and compactors for a weekend unless regular work is planned.
Table of Contents
- Block Paving Repair Kit: The Basics You Need
- Choosing a Block Paving Lifter and Extractor
- How to Fix Sunken Block Paving Step by Step
- The Bottom Line
- Frequently Asked Questions
Block Paving Repair Kit: The Basics You Need
Most block paving repairs fail because the wrong tools for repairing block paving get used. A proper kit starts with a block paving lifter or extractor, a rubber mallet, a bolster chisel, a stiff brush and kiln-dried jointing sand. These tools cover almost every lifting and relaying job.
A block paving repair kit is a small collection of hand tools and materials used to lift damaged blocks, correct the bedding layer and re-sand the joints.
Before buying sand, read this guide to the best sand for block paving. For a larger lift and relay, laying block paving on sand explains the bedding layer that stops blocks sinking again.

Choosing a Block Paving Lifter and Extractor
The right lifting tool depends on how tight the blocks are. A block paving lifter is a specialist hand tool with a hooked or levered end that grips a block and draws it out without damage. For a single stubborn block, flat pry bars or a wide bolster chisel work as a basic alternative; a block removal tool earns its place when several blocks need lifting in a row.
Watch out: levering against the edge of a neighbouring block instead of the joint is the fastest way to chip a paver you then have to replace.
| Tool | Best For | Cost Approach |
|---|---|---|
| Block paving lifter or extractor | Lifting single blocks cleanly | Buy, low cost |
| Bolster chisel and club hammer | Splitting or freeing tight blocks | Buy, low cost |
| Rubber mallet | Settling blocks level | Buy, low cost |
Small hand tools are worth buying outright because they cost little and get reused. Cutters and compactors are better hired for a weekend unless regular work is planned.
How to Fix Sunken Block Paving Step by Step
Fixing sunken block paving means lifting the affected blocks, correcting the bedding layer beneath and relaying them level with the surrounding surface. A persistently sinking driveway often points to a drainage or sub-base problem a contractor should assess.
- Mark out the sunken area and lift the blocks with a lifter or pry bar.
- Scrape back the old bedding sand and check for soft spots or trapped water.
- Top up and screed the bedding layer to a consistent depth.
- Relay the blocks, tapping each one level with a rubber mallet.
- Brush kiln-dried sand into the joints and compact the area.
For a fuller walkthrough, follow these 5 steps to repairing cracked block paving. If the same area keeps dropping, why a driveway keeps sinking explains the causes, and how to maintain block paving driveways helps prevent a repeat.
The Bottom Line
Matching tools to the repair separates a lasting fix from a patch that fails by winter. A modest kit of a lifter, mallet, chisel and jointing sand handles most jobs; hire heavier kit only when the area demands it. For sunken or uneven paving across Norfolk that keeps returning, the bedding or drainage usually needs professional attention. KT Lake Paving and Landscaping offers free, no-obligation estimates, workmanship that meets approved British Standards, and a 10-year product guarantee from Brett.
A driveway that sinks once will sink again without a sound base beneath it. KT Lake Paving and Landscaping can assess the cause, advise on repair or replacement, and install resin bound or paved surfacing built to last. Get started with KT Lake Paving and Landscaping and arrange a free estimate for your Norfolk driveway.
Frequently Asked Questions
What tools do I need to repair block paving?
A basic block paving repair kit covers most small jobs: a block paving lifter or extractor to pull blocks out without chipping them, a rubber mallet to settle replacements, a trowel and screed board for the bedding layer, a stiff brush, and kiln-dried jointing sand. Add safety glasses and gloves before you start. For larger areas, a plate compactor and block cutter help, though many homeowners hire these rather than buy.
How do you lift a block paver without damaging it?
Work a block paving lifter or extractor into the joint at one corner and ease the block up gradually rather than levering hard at a single point. On older paving, run a bolster chisel along the joint first to break the sand seal. Lift from two opposite corners where possible, keep the tool flat against the block face, and set each block aside on grass rather than hard ground so the edges stay intact.
Can you repair block paving with basic hand tools?
Yes, for single blocks and small sunken patches. A claw hammer, bolster chisel, trowel, rubber mallet and stiff brush will get most isolated repairs done. The limits show on larger areas: resetting a whole driveway needs proper compaction and accurate levels, which is where a plate compactor and screeding kit earn their place. If the sinking covers several square metres or keeps returning, it usually points to a sub-base problem worth a professional look.



